The DeWalt DCW210 is a cordless 5″ random orbit sander that is powered by the company’s 20-volt lithium-ion battery system.

Smitten with DeWalt’s 20V Max series of tools, it is a bit like dealing with Apple stuff. I know I’m being played but the products are just darned good. 

Handling is excellent. Weight, vibration level, and control are comfortable. With a top grip, the only option, the sander tends to meet the work squarely with no tendency to tip or gouge. At least with a smallish 2.0 amp-hour battery, balance is excellent. The rubberized area enhances the feel, and the on-off switch is easily accessible from the grip position. 

This is a finishing sander, not a stock removal hog. In that context, it has plenty of power. It is similar to my Bosch ROS20VS, if not more aggressive. The DCW210 has a standard 8-hole base with hook-and-loop disc attachment, and runs with a 3/32″ diameter orbit. The brushless motor is very efficient, so I read. It has a variable speed dial, also accessible from the grip position, but I rarely use that option on a sander. 

You’re going to love this as I do: the motor brake stops the motion immediately when you hit the power switch. Hallelujah!

Dust collection with the onboard bag is surprisingly good but of course, no match for sanding with a vacuum hose. (I vacuumed up the tool nice for the photo.) The bag’s good-sized plastic collar and locking system makes it easy to use one hand to detach and attach with a nice positive click. A spring that lines the bag can be compressed and popped to “shake out” stubborn dust. I find it is more useful for allowing a vacuum hose to thoroughly clean out the bag without it being sucked into the hose. 

The outlet diameter will not fit standard shop vac hoses but this does not matter to me because using a cordless sander with a hose would pretty much negate the advantages of having no power cord. So I will use this sander without tails of any sort.

I cannot offer data on how long the battery charge will last. After a while of sanding, I check the charge-level indicator on the battery and replace it if it is low. With just two extra lightweight 2.0 Ah batteries on hand and using the DCB113 charger, I could keep working indefinitely. You can also buy higher capacity batteries but I guess at some point the weight would get uncomfortable. Anyway, this is a finish sander suited for relatively light work. Note that DeWalt charger models vary considerably in their charge time.

I will still use my bigger Bosch 3725DVS (3/16″ diameter orbit) with its cord and a vac hose for heavier work but the DeWalt DCW210 is now my go-to tool for finish sanding. 

This review is unsolicited and uncompensated. I just want to help you choose good tools. 

My new jig for long-grain shooting accommodates workpieces up to 36″, a big increase from the old jig’s capacity of 24″. I was motivated by a few occasions when I had to use the somewhat awkward setup of clamping a long workpiece to a support board and running the plane on the benchtop. 

I have found that shooting a three-foot long piece is really not a problem with a good setup. And the big jig imposes no disadvantages for shooting much shorter pieces. 

My 10/31/19 post is a discussion of long-grain shooting. 

Construction is simple from 3/4″ MDF: The workpiece platform is 6″ wide on top of the base, which is 9″ wide, to make a 3″-wide plane runway that is covered with thick PSA UHMW plastic. I like the Lie-Nielsen #9 but any bench plane would work.

The workpiece is controlled from the front by the end stop, and from the side with clamped scraps. I find no need for an elaborate, screw-mounted permanent lateral clamp board because while it would offer some convenience, it would also limit the functional range of the jig. Top (downward) control is supplied by your hand. 

When shooting a narrow workpiece, such as a door stile, which might temporarily have a convex or concave non-working edge, there is the danger of the workpiece flexing against the straight edge of the lateral control board. The solution, shown above, is to use two separate lateral control boards, each butted against a section of the (non-straight or suspect) non-working edge of the workpiece. 

The cleat at the right end of the jig is an afterthought (you know what I mean: “Doh!”) that allows the jig to be clamped with dogs with a conveniently minimal opening of the tail vise, which is then tightened. 

It works beautifully.

For the 500th post since the inception of this weblog in 2008, I would like to present the Grand Unified Theory of Woodworking. Concocted while emptying my dust collector, this offers deep insight to woodworkers and non-woodworkers alike as to what really goes on in the shop. 

And so: You start with a tree. Then, to produce a masterpiece you merely remove the exactly correct tiny pieces of wood (as shown in the dustbin pictured above) while retaining the exactly correct wood in the workpieces, which you then simply join together. Done. 

I present this ridiculous notion only to make a couple of points, which are hardly original but bear repeating.

The people who see and use what we make almost never understand the effort, time, skill, and expense required to make high-end woodwork. Perhaps this is only due to the nature of the craft – wood seems so accessible to work. More likely, it is partly or even largely the fault of woodworkers (like me). Most of the things we use in our modern world are made in huge numbers by computer-controlled machinery. In some cases, the consumer’s hands may be the first to ever hold the product. I think woodworkers should affably convey an understanding of what goes into our work to those who encounter it. 

Second, we woodworkers are similarly apt to forget that making excellent stuff is really difficult. Not to be whiny, but it is healthy to acknowledge that we are always dealing with some degree of workmanship of risk from which even the gadgetry of modern woodworking does not shield us. As a mostly subtractive process, woodworking can be unforgiving (again, see dustbin). For me at least, I have to remember to go easy on myself, trust my hard-won capabilities, and be always open to improving my skills.

It’s simple, really.